SunSDR2 PRO - SDR HF Transceiver 20W, 50MHz 15W, 144MHz 8W

SunSDR2 PRO - SDR HF Transceiver 20W, 50MHz 15W, 144MHz 8W

Ref: SunSDR2 PRO

Immediately available

€1,760.50

Tax included

Read the review

Average rating: 5/5 Number of reviews: 1

Usually ships within 24 hours.

Quantity

Guarantee safe & secure checkout

You can purchase this product in installments with Sella Personal Credit. Click here for more information.

Main characteristics

Independent RX path based on DDC (Direct Down-Conversion) architecture
Independent TX path based on DUC (Direct Up-Conversion) architecture
2 RX + SubRX software for each of them (4 slices in total) + independent broadband up to 80 MHz
Remote control operation, using it, you connect PTT and CW key to the E-Coder panel. Microphone and E-Coder are connected to the remotely configured PC
TCI interface for seamless connection with third-party software, the list of software with TCI support
The professional TX processing module offers the most advanced tuning capability for voice operations
ExtCTRL connector to control external devices with 8 powerful open collector keys
ALC connector for external power amplifiers *
Supports the use of VHF transistors **
An opportunity to use the transceiver as a signal generator via DAC OUT connector (SMA connector)
An opportunity to use external filters in the middle of the RF path, using ADC IN and RX OUT (SMA connector)
Small delay in CW mode (about 10 ms)
Input for external 10 MHz reference oscillator
An opportunity to use the transceiver in SO2V mode
Full duplex or half duplex mode ***
Antenna switch with 2 HF antenna connectors and separate VHF antenna connector (Mini UHF connectors)
Internal power meter for HF and VHF bands and SWR meter for HF band
The Ethernet LAN interface provides a fast and reliable connection to your PC

* ** *** These functions are supported by the transceiver hardware, but are not implemented in the ExpertSDR2 software. They will be supported in future releases of the ExpertSDR2 software.

This is the link to Enzo IW7DMH's page where you will find suggestions and everything you need to start using your SunSDR2 and its software

Specifications are subject to change without notice or obligation and specifications are only guaranteed within the amateur radio bands.

RF ADC, bits @ MHz	16 @ 160
ADC type	LTC2209
RX Frequency range, MHz	0.1...65; 95...155
Independent software receivers	2 + 2 SubRX
Sample rate, kHz @ bit	39; 78; 156; 312 @ 24
Bandscope, MHz	80
RX HF filters, MHz	LPF: 65 or 9 x BPF
RX VHF filters, MHz	WideRX: 95-155 or SAW filter for 2M: 144-148
BDR on HF, dB	130
BDR on VHF, dB	114
Sensitivity, uV	0.07
DR IMD3, not less dB	98
RMDR, dB	110
ATT/Preamp, dB	-20; -10; 0; +10
VHF LNA, dB	+22
RF DAC, bits @ MHz	14 @640
TX Frequency range, M	All amateur bands 160-6; 2
Output power on HF, W	15 (up to 20)
Output power on 6M, W	15
Output power on VHF, W	7 (up to 8)
TX IMD3, dB	25-30 on HF/VHF
Local oscillator TCXO, MHz +/- ppm	20 +/- 0.5
External 10 MHz oscillator input	+
Built-in audio codec, bit	24
RF input/output	2HF, 1VHF (Mini_UHF) ADC IN, DAC OUT (SMA)
PC interface	LAN 100 Mbit
DC voltage range in RX/TX, V	10...16/ 12...16
Recommended DC voltage, V	15
Current consumption RX/TX, A	1.25 / 5
Power consumption RX/TX, W	19 / 75
Operating temperature, °C/°F	0...+50/ +32...+122
Dimensions L x W x H, cm/inches	19.0 x 17.0 x 5.0/ 7.48 x 6.69 x 1.97
Weight, kg/lbs	1.5/ 3.31