![E-Coder EP VFO Controller and Functions for SunSDR Transceivers E-Coder EP VFO Controller and Functions for SunSDR Transceivers](https://www.hamradioshop.it/5732-home_default/e-coder-ep-vfo-controller-and-functions-for-sunsdr-transceivers.jpg)
![E-Coder EP VFO Controller and Functions for SunSDR Transceivers E-Coder EP VFO Controller and Functions for SunSDR Transceivers](https://www.hamradioshop.it/5731-home_default/e-coder-ep-vfo-controller-and-functions-for-sunsdr-transceivers.jpg)
![E-Coder EP VFO Controller and Functions for SunSDR Transceivers E-Coder EP VFO Controller and Functions for SunSDR Transceivers](https://www.hamradioshop.it/5727-home_default/e-coder-ep-vfo-controller-and-functions-for-sunsdr-transceivers.jpg)
![E-Coder EP VFO Controller and Functions for SunSDR Transceivers E-Coder EP VFO Controller and Functions for SunSDR Transceivers](https://www.hamradioshop.it/5729-home_default/e-coder-ep-vfo-controller-and-functions-for-sunsdr-transceivers.jpg)
![E-Coder EP VFO Controller and Functions for SunSDR Transceivers E-Coder EP VFO Controller and Functions for SunSDR Transceivers](https://www.hamradioshop.it/5730-home_default/e-coder-ep-vfo-controller-and-functions-for-sunsdr-transceivers.jpg)
Ref: E-Coder
ask for delivery times first
The E-Coder It has a VFO optical sensor that produces 200 pulses per revolution .
In the panel menu, you can view the settings of the
E-Coder control panel. In the Device drop-down menu, you can select
the type of control panel connected. In the meantime, only one is available
type: E-Coder. Note! If an E-Coder panel is connected to the transceiver, the
Panel menu an E-Coder 1 tab appears, if there are multiple E-Coder panels
connected to the transceiver, several tabs appear in the Panel menu
E-Coder 1, E-Coder 2 etc. With identical settings for each panel.
The
control panel function settings menu in ExpertSDR2 programs
In the
left part of the menu, you can see the schematic image of the E-Coder panel
with buttons and knobs. Press any button, you will see the list of functions
available.
The following functions can be assigned to buttons
of the E-Coder panel:
Not used: the button
it is not used.
Principal:
AGC
Up / Down - AGC type switching
Band up/down
- band switching
Filter up/down - switching
of the receiver filter
Up / Down mode - switching
of the mode
MOX - enable/disable mode
manual transmission
PA - enable/disable the amplifier
of power
Preamp Up / Down - level switching
of the preamplifier or attenuator
Power on
/ off - turns the transceiver on / off
RX
ANT - enable / disable the receiving antenna
Step
Up / Down - changes the tuning step
Tone:
enable/disable tone signal in TX mode
WF
- enable/disable wide filter. Filter for the entire Nyquist zone. Self
In the Device menu settings, you set the Enable check box
automatically, you do not need this function on the panel
Zoom
forward / backward - switching spectrum zoom modes
VFO
/ RX2:
A>B - assigns frequency from heterodyne
VFO A to VFO B heterodyne
B>A - assign frequency
from VFO B heterodyne to VFO A heterodyne
B <>
A - frequency swap between VFO A and VFO B
Change VFO
A / VFO B - switches between VFO A and VFO B
IF as RIT -
adjust the RIT offset by moving the filter across the panorama
BLOCK
- locks frequency tuning
RX2 On
/ Off - enable / disable RX2
RIT On / Off - enable
/ disable RIT offset
RIT Reset: Resets the offset
RIT at 0
Sub RX On/Off - enable/disable SubRX
Divide:
enable/disable Split mode
Change DDS
/IF: Tunes the frequency by moving the filter across the panorama, in other words
changing the digital IF or when the filter stops and the spectrum shifts, this
is the tuning of the center frequency
Switches
Receiver - switching between RX1 and RX2 software. The main knob will tune
the frequency of one of the receivers
XIT On / Off - enable
/ disable XIT offset
XIT Restore - restore
the XIT offset to 0
While using RX1 and RX2, it is generally necessary
listen to just one of them or both, but on different channels (left/right).
To do this we have added special functions to the E-Coder panel, which sets
the mixer for both RXs
Audio:
Listen
both RX1, RX2 - default settings, both RXs have the same volume
in both channels
Listen to RX1 only: Listen to RX1
in both channels
Listen to RX2 only: Listen to RX2
in both channels
Listen to RX1 in the left channel,
RX2 in the right channel - listen to RX1 in the left channel and RX2 in the right channel
Listen
RX1 in right channel, RX2 in left channel - listen to RX1 in right channel and
RX2 in the left channel
Similar settings have been added for i
VFO:
Listen to both VFO A/B - settings
By default, both VFOs have the same volume in both channels
Listen
VFO A only - listen to VFO A on both channels
Listen
VFO B only: Listen to VFO B on both channels
Listen
VFO A in the left channel, VFO B in the right - listen to VFO A in the left channel
and VFO B in the right channel
Listen to VFO A in the channel
right, VFO B in the left channel - listen to VFO A in the right channel and the VFO
B in the left channel
Mute: Turn off the sound
Change
RX and mute previous - change the receiver software and mute the audio
previous
TX / Play - switches to TX and plays the signal
recorded in the air
Voice Recording: Enable /
disable voice recording
Volume up/down
- volume adjustment
DSP:
ANF
- enable/disable automatic notch filter
APF
- enable/disable analog pick filter
BIN
- enable/disable binaural mode
NR - enable
/ disables noise reduction
NB1 - enable
/ disable noise blanker 1
NB2 - enable / disable
the noise blanker 2
SQL: enable/disable squelch
The
following functions can be assigned to the E-Coder panel knobs:
Not
used: the encoder is not used
Volume - adjustment
of the volume
Microphone Gain - Adjusting the
microphone gain
SQL: Threshold adjustment
of squelch
Low/High Filter: Tune the frequency
of the front of the low/high filter
Length
filter - filter width adjustment
Filter
Shift: shifts the center frequency of the filter
Drive:
regulation of the output power
IF - tuning
of the frequency by moving the filter on the panorama
I earn
RF - RF gain control
CW Speed - Control
CW speed
Data sheet