LDG AT-200PROII  Accordatore D'antenna automatico

LDG AT-200PROII Accordatore D'antenna automatico

AT200PROII
Non ci sono abbastanza prodotti in magazzino
265,00 €
Tasse incluse

Puoi acquistare questo prodotto con Sella Personal Credit. Clicca qui per maggiori informazioni.


width=129

LDG AT-200ProII

 

Time was, 100 watts was a lot of power. Today, more and more transceivers feature 200 watts output. Even though many of these modern radios feature a built-in tuner, it's range and features are usually quite limited; if you need a tuner, you probably need a better one than they built into the radio. The LDG AT-200ProII is designed for this new generation of rig. It's specifically recommended for Ten-Tec and tube radios. Many QRP operators have a small 100-150 watt amplifier for times when you need a few more S-units. The AT-200II is ideal for this kind of operation; it's minimum required power is only 5 watts, but it will handle the higher power as well.

The AT-200II will handle up to 250 watts SSB or CW on 1.8 - 30 MHz, and 100 watts on 54 MHz. It features LDG's state-of-the-art, processor-controlled Switched-L tuner. It will match virtually any kind of coax-fed antenna, including Yagis, dipoles, inverted Vs, slopers, loops, just about anything. It will typically match a 10:1 SWR down to 1.5:1 in just a few seconds. You can also use the AT-200ProII with longwires, random wires and antennas fed with ladder line with the optional LDG balun.

Operation couldn?t be simpler: while transmitting a carrier, just press the Tune button. An automatic tuning cycle will begin, then end a few seconds later with the tuner set at the lowest SWR (almost instant for frequencies stored in memory).

The AT-200ProII is the latest in a long line of innovative LDG tuners. Get the most out of your Kenwood, Yaesu, Ten-Tec or Icom radios that operate at higher power.

Specifications:

 

 

 

  • 5 to 250 watts SSB and CW. 100 watts on 6M. 75 watts with PSK or digital modes.
  • Easy to read LED bargraph display for RF power, SWR and status
  • LEDs for Antenna Position and Bypass
  • 4,000 memories (2000 for each antenna) for instantaneous band changing
  • Two position antenna switch with memories for four antennas on each position
  • Tuning time: 0.5 to 6 seconds full tune, < 0.1 second memory tune
  • Built in frequency counter for memory operation
  • Frequency coverage: 1.8 to 54.0 MHz.
  • Tunes 6 to 800 ohm loads (16 to 150 ohms on 6M), 6 to 3600 ohms with optional 4:1 Balun (LDG RBA 4-1)
  • For Dipoles, Verticals, Vees, Beams or and Coax Fed Antenna
  • Optional external Balun allows tuning of random length, long wire or ladder line fed antennas
  • Includes 6' DC power cable
  • Power requirements: 11 to 16 volts DC at 750 mA max during tuning
  • www.Jameco.com WM1012-760 and 1953663 are compatible power supplies
  • Enclosure: 9.5D x 7.1W x 2.0H inches
  • Weight: 2 pounds
Marca compatibile
Generico
Tipo
generico

16 altri prodotti della stessa categoria:

Product added to wishlist
Product added to compare.

Questo sito web utilizza i cookie, Accetta Cookies & Policy Sulla Privacy?

Utilizziamo i cookie per personalizzare contenuti ed annunci, per fornire funzionalità dei social media e per analizzare il nostro traffico. Condividiamo inoltre informazioni sul modo in cui utilizza il nostro sito con i nostri partner che si occupano di analisi dei dati web, pubblicità e social media, i quali potrebbero combinarle con altre informazioni che ha fornito loro o che hanno raccolto dal suo utilizzo dei loro servizi. Acconsenta ai nostri cookie se continua ad utilizzare il nostro sito web. Ti Ricordiamo che Ogni 30 Giorni Ti sarà richiesta questa conferma, Leggi la Nostra Privacy Policy Completa