Remoterig - Rotator Control Unit 1216L

1216L-5 Rotator Control Unit

1216L
Ultimi articoli in magazzino
155,93 €
Tasse incluse
rating Nessun opinione al momento
Spedito generalmente entro 24 ore.

Puoi acquistare questo prodotto con Sella Personal Credit. Clicca qui per maggiori informazioni.


height=

Rotator Control Unit 1216L

 

Per creare un web based di controllo dei rotatori La centralina Rotator (RCU) è collegato al Webswitch 1216H. Il telecomando è collegato tramite il bus 1-wire per il webswitch. Il telecomando ha tre 16A relè per la rotazione in senso orario e antiorario e per il controllo del freno. Per la lettura azimut (direzione) vi è un ingresso / D che gestisce 0-7,5V o 0-15V. L'ingresso A / D è completamente issolated. Il telecomando può essere collegato alla maggior parte degli attuali rotatori disponibili e rotori torri. L'indicatiore può essere calibrato ogni 30 gradi per gestire potenziometri non è lineari.

Quando si utilizza il Webswitch e il telecomando non è necessario utilizzare le porte RRC-seriali per il controllo dei rotatori.

 

To create a web based rotator control the Rotator control Unit (RCU) is connected to the Webswitch 1216H. The RCU is connected via the 1-wire bus to the webswitch. The RCU has three 16A relays for CW and CCW rotation and for brake control. For the the azimuth (direction) reading there is  A/D input which handles 0-7,5V or 0-15V. The A/D input is fully issolated. The RCU can be connected to most of the current available rotators  and rotating tower controls. The indicatior can be calibrated every 30 degrees to handle potentiometers which is not linear.

When using the Webswitch and the RCU you do not need to use the RRC-serial ports for rotator control.

height=

Installation

The Rotor Control Unit 1216L (RCU) is connected between the Webswitch 1216H and the Rotator Control box.

The  RCU needs 12V power, an easy way is to connect it in parallell with the power to the Webswitch. Note! If you connect 12V to the Webswitch via the circular 2.1/5.5 mm DC-connector, + must be in the center.

The RCU gets it’s control signal trough the 1-wire bus from the Webswitch, either Bus A or B can be used, we use Bus B in the example above.

The relays are connected in parallell with the switches on the ordinary control box. The relays can handle <20VDC/16A, <30VDC/10A or 230VAC/16A

The Pot (A/D) input is connected in way that it will sense a Voltage between 0-15V depending on the direction of the Antenna.
There are calibrations points at every 30 degrees so the input volatage do not have to be 100% linear.
The input Inpedance is >220K  so it can be connected almost everywhere. The Pot Input is fully issolated from Ground.

Attention! If you connect the RCU to a HAM or CDE rotator remember that the break relase button is connected on the primary side of the transformer.
The RCU handles 230V but you have to be careful when doing the installation, keep to protection cover on the back of the PCB and mount the RCU inside the Rotator Control Box.

height=

Set Up

Before you can use the Rotator control unit 1216L, there is a few steps which have to be done. First do the hardware installation, after that do the following.

Browse to the Webswitch 1216H, and select the “Rotator Settings” link at the menu to the left.

 

 

image

Set rotator to “Analogue” and press the  “Submit” button.

Later on you can program the Presets here, I think it’s quite intuitive.

Then select the 1-wire link at the menu to the left.

image

Then press “Scan BUS-A or B for new devices” depending on which bus you have connected the RCU 1216L to.

If everything is OK the Webswitch will indicate that it has found a A/D converter eg the RCU 1216L.

You can now change the name to something which is easier to recognize, for example Rotator.

The press the  “Submit” button.

image

Now select the “Rotator” link at the menu to the left.

image

Then press the “Settings” link.

image

You will now see the Rotator settings window.

Enter “Scale start” value, If your indicator scale starts from 0 set 0, if it’s 180 set 180.

If your antenna is not mounted exactly accordning to the indicator you can set an “Antenna Offset” value.

In the sensor field select the sensor you scanned and renamed before, in this case “Rotator”.

The “Fine tuning” can be used if the antenna will go to short or to long when used fixed values, leave it at 0.

Press “submit” button.

From your ordinary Rotator control box turn the antenna fully Counter Clock Wise (CCW).

Press the first button “0″ or  “180″ ( depending on where your scale starts) to learn the RCU A/D value indicating antenna fully CCW.

From your ordinary Rotator control box turn the antenna fully Clock Wise (CW).

The A/D value on the bottom of the page will Increase or decrease  now.

When its fully CW, press the last button “360″ or  “180″ ( depending on where your scale starts)  to learn the RCU A/D value indicating antenna fully CW.

Then click on the link on the top “Fill in missing calibration settings………”

image

If your rotor indictor potentiometer is linear the settings are done now.

Now select the “Rotator” link at the menu to the left again.

Now test to rotate the antenna with the ordinary control box  and compare the direction on the control box and the “Web” values.

If they follow each other the Potentiometer in the rotor is fairly linear an everything is OK.

If the pot is not linear you can set the values manually buy pressing the calibration points buttons.

image

When the setup is done you only need the rotator window in the future. It’s quite Intuitive I think.

You can turn the antenna CW or CCW manually by pressing and hold the CW or CCW buttons. The buttons vill change from green to red when the rotator is turning the antenna.
You can also  set a direction by entering the wanted direction in the box and press the “Go!” button. The Rotator will the go to the right direction automatically. You can stop the rotation by pressing the “Stop” button

image

The “Brake Released/Activated” LED will indicate when the brake is released, It will be released a moment before the rotation is started and activated a few seconds after the rotation has stopped.

The “Live Update Active/Not Active” will indicate if the window is showing Live values, It will change to “Live Not Active” after about 30 seconds of no activity.

Have fun……

Mpn
1216L
Tipo
generico
Marca compatibile
Generico

I clienti che hanno acquistato questo prodotto hanno comprato anche:

16 altri prodotti della stessa categoria:

Product added to wishlist
Product added to compare.

Questo sito web utilizza i cookie, Accetta Cookies & Policy Sulla Privacy?

Utilizziamo i cookie per personalizzare contenuti ed annunci, per fornire funzionalità dei social media e per analizzare il nostro traffico. Condividiamo inoltre informazioni sul modo in cui utilizza il nostro sito con i nostri partner che si occupano di analisi dei dati web, pubblicità e social media, i quali potrebbero combinarle con altre informazioni che ha fornito loro o che hanno raccolto dal suo utilizzo dei loro servizi. Acconsenta ai nostri cookie se continua ad utilizzare il nostro sito web. Ti Ricordiamo che Ogni 30 Giorni Ti sarà richiesta questa conferma, Leggi la Nostra Privacy Policy Completa